The printer is damaged shall not be discarded into the trash just yet. You can fix it yourself at home there are a few possible reply cause printer can not print, here for example:
1. Printer Connections-check the connections with electrical network printer in your home – make sure the printer power cable has been plugged into the power cord connector perfectly
2. Switch Printer-make sure the switch is "on-off" button switches the printer or the printer in the position "on
-The problem is not the existence of the power to the printer is usually marked with an indicator light not lit, the printer uses for the indicator light to the power indicator.
3. USB cable data cable connections-check printer, if connected to the parallel port/USB port on the computer or leptop correctly-try to use another printer data cable as an experiment > Kalo PAL using a Microsoft Windows operating system, and using a printer connected to the parallel port of the reply in the The intent of the above command is to deflect the results display "dir" command (command to list displays the contents of a directory) of the reply should be to monitor but the computer's parallel port to be sure to install > driver for the printer.
> Verify driver has chosen a proper reply to the printer used.
> Verify has chosen port yg right for printer
Try using standard > text editor application to create the operating system print something Reply text editor application can print, then it is likely the fault is not on the printer.
Try to change the settings of the Default printer > became "Printer"-or try to reinstall the printer driver by the name of the printer and change the new installation as the "Default Printer".
Be sure to have the hard drive space > write. Sometimes the reply buffer was not enough, then the data is sent to the printer can not perfectly.
> Try to change setting "spooler" to printer through printer properties menu.
Features "spooler" is used with the purpose to be able to run the application when done printing the document.
Check whether there is any resource > reply conflict with the ports used by the printer. Use the help of the "hardware troubleshooter" reply in case of conflicts. This case might also be caused by the computer's propertied troubled port.
> Kalo steps above already done but not found "bright spot", try to move the printer port connection to another port or try the printer on another computer
Tips printer
,
Tutorial printer
1. Printer Connections-check the connections with electrical network printer in your home – make sure the printer power cable has been plugged into the power cord connector perfectly
2. Switch Printer-make sure the switch is "on-off" button switches the printer or the printer in the position "on
-The problem is not the existence of the power to the printer is usually marked with an indicator light not lit, the printer uses for the indicator light to the power indicator.
3. USB cable data cable connections-check printer, if connected to the parallel port/USB port on the computer or leptop correctly-try to use another printer data cable as an experiment > Kalo PAL using a Microsoft Windows operating system, and using a printer connected to the parallel port of the reply in the The intent of the above command is to deflect the results display "dir" command (command to list displays the contents of a directory) of the reply should be to monitor but the computer's parallel port to be sure to install > driver for the printer.
> Verify driver has chosen a proper reply to the printer used.
> Verify has chosen port yg right for printer
Try using standard > text editor application to create the operating system print something Reply text editor application can print, then it is likely the fault is not on the printer.
Try to change the settings of the Default printer > became "Printer"-or try to reinstall the printer driver by the name of the printer and change the new installation as the "Default Printer".
Be sure to have the hard drive space > write. Sometimes the reply buffer was not enough, then the data is sent to the printer can not perfectly.
> Try to change setting "spooler" to printer through printer properties menu.
Features "spooler" is used with the purpose to be able to run the application when done printing the document.
Check whether there is any resource > reply conflict with the ports used by the printer. Use the help of the "hardware troubleshooter" reply in case of conflicts. This case might also be caused by the computer's propertied troubled port.
> Kalo steps above already done but not found "bright spot", try to move the printer port connection to another port or try the printer on another computer
No comments:
Post a Comment